Savagecat's Progress Thread

You can get the list of parts for a 99 DOHC Mustang here:
http://www.vortechsuperchargers.com/kitlist/4FR218-010_list.gif

This is what I used from it:

1. Oil Feed Assembly

2. Oil Drain Assembly

3. Coolant Pipe Assembly

4. Discharge Assembly

5. Mounting Bracket Assembly (I only used the belt and Idler pulley parts and then theres like 4 or 5 other bolts that hold the bracket to the block, if you call and talk to someone you can tell them and they'lle give you the correct bolts, I don't remember exacly whch one they are).

6. Supercharger Assembly (The 3.6" pulley will put out around 6PSI)

7. The Vortech intake tube wouldn't fit between the fan and engine so I bought a 4" 45 degree tube and a 3.5" to 4" 90 degree rubber hose from intakehoses.com, then I just used a lightning MAF and KN filter. Siliconeintakes.com has some pretty good stuff too.
There is an a/c line you have to bend to get it to fit and I still had to trim the fan shroud alittle and mount it down about an inch lower to get it to fit in there.

8. Ford Racing 42lb Injectors

9. 255lph fuel pump form SCP
 
Sorry if thats a little unorganized there might have been a few miscellaneous things that I left out but should pretty much be everything.
 
I also bought a 3.33" pulley that should bring it to around 9PSI I hope, but I'm not gonna put that on till the spring cause I don't feel like paying for another tune this year.
 
Oh yeah I almost forgot the air pump and hoses, in the mounting assembly they offer part to reroute it, or you can bend the crap out of the hoses like did, or just remove it, if you don't the oil drain hose won't fit in there.
 
I finally recieved my SC back from 928 Motorsport yesterday and am alittle angry I don't know if its a big deal or not but the good used impellar that they sold me has a couple knicks in it I just emailed them to see what the deal is with it

Honestly I wouldnt buy a used impellor but thats just me. I would bite the bullet and get one thats new or get the billet one. Better safe then sorry.

:iconcur:
 
Just get a vale or wear a ring and soak it in bleach, then drop it in your sample. These will only work for grass. If your smoking crack you problably wouldn't have a badass mark. You'd have smoked it by now.
 
I probably smoke weed once or twice a month and I happen to have to get a random drug test two days after I smoked, I got some drink called qcarbo from GNC I heard it works so hopefully it works, if not anyone want to buy my SC setup
 
If you only smoke once a month then you wont test dirty unless you spend that whole day smoking non stop. Cheats dont work. Why they SEEM to work is because how much water they have you drink. Just drink the water and you will accomplish the same results.
 
I used to buy the synthetic pee from the headshops...as long as they don't actually watch you peeing, they work great
 
Someone wanted me to update my thread so here ya go

081.jpg


082.jpg


083.jpg


084.jpg


085.jpg


086.jpg


087.jpg


088.jpg
 
I didn't end up getting to New England Dragway last weekend so I'm kind of bummed about that cause it was the last week they were open until April.
 
I think next years mods are going to be:

Smaller pulley good for around 9PSI
Intercooler
Kennebelle Boostaspark
Better Tune
Front subframe connectors
Rear Brace
Pinion Brace
Dennys 4" Driveshaft
Some Body work and paint
Front end rebuild
 
I already got it tuned I'll get it tuned again in the spring when I put the other pulley on it, I gotta try to get them to email me a copy of the my dyno results, it made 311hp and 270 ft lbs, but I think it should have made more torque, plus my check engine light is on for running too rich and the idles alittle shakey so I think I'm gonna go somewhere else next time.
 
When I end up installing an intercooler do you think I should go with a water to air cooler or a air to air cooler any opinions
 
There is so much room for a FMIC that its almost a crime not to have one.
 

Members online

No members online now.
Back
Top