Search results for query: *

98 engine swapped into a 2000 Mazda and I'm trying to get the tach to work:confused: Tried hooking up the tach to ECM pin 48 as this what was used in the Mazda, but no worky:confused: Do I have to buy a tach signal generator in order for it to work??? How does the tach work on a second...

Does anybody have the torque specs and tightening sequence for the Cobra Intake swap???? Thanx:)

I'm currently trying to get my sniper tune straight in my truck. It's a 2000 Mazda with a 98 Mark VIII engine. The problem I'm having is it seems to fall flat on top:confused: Off the line is decent, but when I go open throttle it seems to go no where. I did a datalog and the timing never seems...

Does anybody know where I can buy an Intake Hardware Kit for the 98 Cobra upper/lower bolts??? Max says most of them have been discontinued from the dealer....... Thanx:)

Does anybody have a pic or can explain what the EAM relay looks like. This is the relay used on 2nd gen's to inject air into the catalyst for the first few minutes of running? Location won't help as the car has already been parted. I need to use it for a swap that I'm doing. Thanx:)

Does anybody know if the air bag's from a mark will work in a 95 town car??? A guy at work needs some bags and I have some and was going to help him out. Thanx:)

I'm putting a 98 4.6L DOHC in a Mazda Truck and have been trying to get it started. What appears to be happening is the PCM is not grounding the fuel pump relay so it will turn on. As soon as I ground the lead the pump will turn on and it will fire. I flashed the PCM with Sniper and...

Has anybody run a belt without the A/C compressor installed, if so what size did you use?? I'm in the process of doing a swap into a truck from a 98 and will not be using the compressor and basically bypassing it. Thanx:)

Does anybody know if they make wiring diagrams for the gen 2's showing the connectors?? I have the factory book and it shows the connectors, but I was looking for a complete sheet showing the wiring with the connectors, very similiar to the way the earlier ford schematics are for our cars. Thanx

I am in the process of putting a 98 trans in my 93. Do I need to swap out the TCC solenoid? I keep reading conflicitng info. on whether I need to swap it out or not. Thanx:)

The other night while leaving a restaurant, I was backing out onto a hill and noticed another car was also backing up into my car. Well to avoid the hit I slammed the gas hard, now my tranny is shifting late from 1st gear. It will also downshift into first almost all the time and stay there...

I recently installed an exhaust system that I obtained from a car I parted out. It's 2 1/2" from the cat back with the third cat. and resonator removed. The mufflers seem to be a turbo type, don't recogonize the name. The car is not very loud, but it resonates in the cabin bad at times. I would...

I have a 93 Mark VIII that has an intermittent stumble on occassion. After the stumble the check engine light will come on. The codes I am getting are: 172 Heated oxygen sensor indicates lean condition, right side 176 Heated oxygen sensor indicates lean condition, left side 543 Fuel Pump...

I have a car I bought for parts and was planning on removing the engine soon. I see the easiest way is to remove from the bottom. Does anybody have any ideas on how to get the car up that high? I seen one post where a hoist was attached to someone's roof in their garage, but not sure I trust my...

I recently purchased a 93 mark VIII that has the dreaded timing chain tick/clack. It only does it when cold(about 10min.) and is quite loud, going away when it warms up. I know adding synthetic(next on to do list) and changing to correct oil filter which I already have will quiet it some, but is...