Search results for query: *

I'm not expecting mineshaft air, but the DA should be just under sea level. :cool: Stop by if you're in the area. ;)

I've never paid much attention to posts about Gen 1's, so this probably has already been posted. :rolleyes: I installed a pair of HID housings and an aftermarket HID kit (using my adapters, of course :cool:) in a '94 today, and was suprised to find that I had to modify the header panel in...

So-so air (DA 361). Still more left in the tune. :cool:

Looks like the air should be pretty good. :cool: Unless you've got friggatriskaidekaphobia. :p

If you have a rattle, it might be a broken door glass retainer. This is the rear track that the window descends into as it is lowered. Even in my low mileage originally Florida car, rust ate through the spot welds. :( The Ford p/n is F3LY63222A01A, and it is obsolete, although Vintage Parts...

Tomorrow I start bolting everything back together. More details here: http://www.lincolnsofdistinction.org/vbulletin/showthread.php?t=34748 Here are a few teaser pics. :cool:

Decided to finally do a J-Mod and install a temp sensor in my LPW pan. After looking for it a bit, I did some research and found that '98 4R70W's don't have the screen (1st pic) that the earlier transmissions had. Discovered that the lower 1/2 spring was broken in half (2nd pic), which...

I recently installed some new Firestone 275/40-17 tires on 17x9 rims with a 36mm offset on the rear of my '98 LSC. I ran into some clearance issues, so I bought a new toy. :D I released the air in the rear bags, disconnected the sway bar and jacked up the wheel/tire to see where the problem...

The stock two piece spacers for the forward strut rod bushings are obsolete. And usually, they're rusted to the point of having to be cut off on northern cars. Such is the case with the car I currently have on my lift. So in order to install new Ford forward bushings (E9SZ3B271A...

Sloppy work and shortcuts. :eek:

Has anyone installed UD pulleys on a Gen 2 and retained the Secondary Air Injection Diverter Valve? It won't fit without modification as the front of the March balancer is solid. Also, does anyone have a diverter valve for sale? If I decide to keep it, I'm going to need a new one, this...

Again, working on someone else's northern '98. I wish that Ford would have used anti-sieze during assembly. Without it, steel bolts and aluminum can become corroded, and the result is pulled threads, and bolts that are very difficult to remove. I'll have to chase all of the threads, on...

I'm doing some work on someone else's '98 and I thought I'd post a few pics of what I've had to do so far to remove the Sub-Frame bolts in order to replace the forward Sub-Frame support brackets. This will give anyone who's looking at doing this job an idea of what you're getting into on a...

My new Cobra intake and some tuning produced this. The DA was 1,464 ft., with better air I should be able to get into the 13.6's.

Is this the Holy Grail? Shown as a new product on Canton's web site. http://www.cantonracingproducts.com/cgi-bin/commerce.cgi?preadd=action&key=13-780 Summit shows that it fits Mark VIII's and Thunderbirds. $200.95...

FWIW I've seen a few posts recently about people that have ADDCO front sway bars, but not the locating collars. I ran across THIS company that makes them, in various sizes and materials. If you search for their part numbers on Amazon, there are quite few companies selling them.

The DA is pretty good (-590 @ 10 am) and I doubt if it will be this good again until the fall. :D I'll be there around 5 pm. CRAP! Scratch that, motorcycles only tonight! :mad:

I have found that the ODB-II RPM and MAF voltage using the OBD-II Innovate Motorsports cable (p/n 3809) is VERY unreliable. :mad: So, I decided to use the analog cable (p/n 3811) to get what I needed. I had read that in order to get a tach signal from a Gen 2 that you need a tach adapter...

Since I was taking the DR's off my car today, I thought I'd shoot some pics showing the three different wheels that I have. All are FRPP wheels, and all are the 5 x 4.5" bolt pattern. The first pic is a 17x9" M179 Cobra R wheel with +36mm offset. The tire is a MT 275/40-17 DR. The second...

...Make sure that you trim the hood pad retaining tab on the back of the hood! ;) Otherwise, this will happen. :eek: Not mine, thank GOD, but someone else's car I saw @ Englishtown.