Recent content by beatcpl

Hi, All The Pic tells everything. If happened while I was tightening the lower mount nut. Is it possible to replace the shock mount? Thanks in advance.

Hi, All Happy New year!. I've been installed the Kensun HID conversion kit in my mark viii 1977. But, It often shuts down electronic systems when I'm turn on the headlight at night. then, I found out that it is related to Anti-theft system since I didn't installed the relay. Is it possible to...

Hi, All My seat motor is not working anymore except tilting. I did this Seat motor repair tips (long) And I found out that two motors thread has been worn out. is there any possible to move the seat forward manually ?.... My foot is too far away from the accelerator pedal. Thanks, 97...

Hi,All I'm looking for new tires at local. This is 2012 Ford Focus Mk3 MK5 stock wheel and 2013 Ford Fusion 18" oem wheels. Is wheels fit at Mark VIII? 2012 Ford Focus Mk3 MK5 stock 17"wheel WHEELS SIZE IS E7.0Jx17H2 BOLT PATTERN 5x108 mm OFFSET ET50 P225/50R17 93V M+S MICHELIN GREEN GAS...

thanks for reply... gen1 air pump will fit gen2 or thunder bird part will fit in gen2?. thanks

Happy New Year everyone!!! I've gotten check engine light in a while - (P1414 Smog pump issue). is there any possible to turn off the smog pump? or better replace it. thanks

Hi, I'd like to add a led strip 5630 RGB led strip( 1m: 14w) around the front grill when the parking is light on the night time. Where is safe place hookup the wire? and I'd like to change a color by remote too. here is example photo of project. thanks,

I’ve done rebuild a front suspension, Lower Arm, inner/ outer tie rod, Stabilizer Link, Strut rod bushing – Moog K8680 (front to lower arm). Front to Frame bushing frame was fine. After i Installed them, I did the alignment at Firestone. After 200miles, I checked the front suspension again...

Thanks for your input Unity Here is I found at internet.. it is interesting. http://www.city-data.com/forum/automotive/2039574-tightening-lower-control-arms.html But, I'll follow your instruction but, I don't have enough tools . So, I'm thinking, I'll torque bolts as a lower torque requested...

I totally agree with My Great 8's idea. Standard strutmasters kits will popping your rear side when your gas is low. standard kit you will need babels in your trunk that rear side sat down or You might be drive a full gas all the time due to Standard kit's rear spring sits higher than rear air...

Thanks for you input soduka, Actually i bought the inner / outer tie rods, Strut rod bushing. When I dissembled the suspension part, They ain't bad. So, following your advice, I'll keep old part of inner / outer tie rods, Strut rod bushing since they are decent shape without any noise Thanks...

Do I have to replace suspension parts by age or If the parts still look good, better keep it? For example, inner/outer tie rod, strut bushing and stabilizer link while I'm replacing a lower arm. Car mileage is 61,000 Thanks,

I'm going to replace front end(LCA, strut rod bushing and tie rod). I recently read in the factory manual that the suspension must be on the ground when you tighten the nut or bolt . I'm not sure how to do this. I thought , just set jack and stand underneath a car and loosen the bolts on the...

Hi, All I just purchased a Raybestos 507-1397 Professional Grade Control arm at Ebay. But, There is "BAW " logo in the mid of Lower arm. But, I can't seem to find the information of "BAW" web site or Raybestos web site. Has anyone had the same experience? Thanks Here is pics Ebay...

Just I found... the link is still working condition. If someone need a CD, here is Link https://yadi.sk/d/N87JRkGiFgoBf or here is the dvd iso image: https://docs.google.com/uc?id=0BzuBJ...xport=download Here is original link...