Search results

It is not for any engine code. I accidentally physically damaged the old one. Tony

For reasons that I'll not go into, I need a new throttle body. I'm seeing that the computer might have to "relearn" the throttle body. How do I go about doing that? Is it a simple matter of resetting the ecu? What do I have to do once the throttle body is installed? Thanks for your help. Tony

I'm having the same leaking issue from the back of the engine (right at the bell housing/transmission joint). I'm 99% sure that the leak is originating from the water outlet pipe (behind the thermostat), running under the intake manifold and falling off the rear of the engine. With that said, it...

I've cleaned everything, and replaced the filter. It just feels like the signal from the pedal to the throttle is delayed. It's hard to merge into fast traffic when you have factor in a 1/2 second delay. Tony

Hello all, For some time now, I've had a bit of an issue with the throttle response on my wife's 04 LS. It takes about 1/2 a second to respond to any input. If I mash on the gas and let off fast enough, It's like I didn't do it at all. I suspect the issue is in the sensor in the throttle. I know...

Thanks. That was next on my list.

Thanks for all of your help so far. I have a question for you. For the rear view camera; The lamp seems to be negatively triggered (think that is the term...both leads to the reverse lamp are +12v until in reverse, and then one goes gnd to light the bulb). How are you wiring the relay to power...

Question for you; Are you triggering both amps with the same remote out signal from the JVC? I'm putting in the kw-nt300 and it only has one remote out. Are you tying both 2.2k reisitors to that and then on to the amp triggers? Thanks. Tony

So you're saying the speed signal is in the back? Weird place for it. So you used pin 9 to get the signal up front for the head unit. OK I get it. Thanks Tony

Pictures of the camera install? Also, I didn't see it anywhere in the diagrams; Did you use the speed pulse signal for the JVC. If so, where did you get the signal from? Tony

Pictures of the camera install?

Thanks. And can you post a link to the LS Dash Kit you used?

I do have the THX/Nav/Factory Amp system. So, if you can, please send me the diagrams. Also, according to the site, this harness is for the NAV/AMP systems: FCSS-2P This Bluetooth harness adapter, FCSS-2P is designed for Ford amplified, NAV, or mute on the radio vehicles using the Parrot...

FYI. I found this harness for those of you not looking to hack the wiring in the car. It's designed for a bluetooth add on module, but it should allow for a plug and play stereo install: Ford Harness As I added bluetooth a few years ago, I might actually have this in my car already (I don't...

Joegr, I'm about to install the kw-nt500 in my wife's car. I have a couple of questions. First, can you send me the diagrams? Second. did you have to buy an after market mounting kit, or did the metal frame that came with the unit work well enough? Did you use the RCA pre-amp outs on the JVC to...

I especially like the fact that there is no foot on the gas peddle.

FWI; I did get the car and trans up to temp before putting it up. Tony

OK... I agree with you....but....I put the car up again, leveled it, pulled the center plug, and the rear filler plug, and as soon as I start adding in the rear hole, it started leaking from the center drain hole. What is going on here? Any help? Thanks. Tony

Hello all. I'm looking for a little help. I changed the trans filter and was filling the pan back up. I was only able to put about 3 1/2 quarts into the pan before it started leaking out of the drain (seems like not enough). I took it for a drive to warm up the trans, but when I come to a stop...

Anyone figure out how to take the delay out of the Gen 2 electronic throttle? This has been an annoying issue on my 04 3.9. Thanks. Tony