Search results

Obsolete Strut Rod needed or where to find Obsolete Ford/Lincoln part, this is the mildly shaped S curved piece that connects to the lower control arm forward to the frame, which are affixed the common to find strut rod bushing kits; to frame, to arm Problem; The rusted end nuts of the...

Obsolete Ford/Lincoln part, this is the mildly shaped S curved piece that connects to the lower control arm forward to the frame, which are affixed the common to find strut rod bushing kits; to frame, to arm Problem; The rusted end nuts of the bushing and washers to the threaded strut rod...

Obsolete Ford/Lincoln part, this is the mildly shaped S curved piece that connects to the lower control arm forward to the frame, which are affixed the common to find strut rod bushing kits; to frame, to arm Problem; The rusted end nuts of the bushing and washers to the threaded strut rod...

swapped wire seven and six runs allot better now

thanks, Taken a second look This is how I set up the wires to the plugs but something does not feel right Left coil 1_2.......................right coil 3_4 7 3............................6 2 1 5............................4 8 Something tells me wires 7 and 6 are mixed up??? + 1&6 - coil...

To clarify the question is the firing order 1 3 7 2 6 5 4 8 Pass side cylinders 1 2 3 4 Driver side cylinders 5 6 7 8 What I'm unclear is the left and right coil packs, ok they are labeled. I'm just not putting it together some how, what would help is pass side coil pack connect wires ...

swapped my broken valve '95 motor for a '97. I think I may have misdirected two wires to the wrong cylinders although the '95 coils are labeled, I'm not sure if I ran the wires properly. I used the search and have not com across a plug/wire wiring diagram. Do the gen1 and gen2 use the same...

Spring wise the original springs have been discontinued by Ford and replaced with currently a discontinued springs by Ford. Best bet would to find a junk yarded F250 or heavier truck with 4R70W transmission and scavage a 1-2 brown spring for a stiffer upper spring. For the lower use the 3-4...

F2LE B2A blue top injectors? DENSI With a strong light and reading glasses it will have the stamping where the blue top stops and the brownish bottom of injector starts. 24 lb/hr, F2LE-B2A, Lt. Blue 4.6L DOHC

How do I put it back together Was wondering what that rubber plug was for...anyway the nuts on the torque converter needed a big impact to come off. Went as far as adding a new tool, two eighteen inch one inch pipes as a cheater wrenches to slip over the handle of ratchets and wrenches...

Was being sarcastic and making a joke out of my car, which it is and does pull to the right; think my problem is the strut arm on the pas side is cranked to deep or brakes hydraulic box is fugd. He is pretty lucky that the arm and rim bent. Good to hear rubber side stayed down and only minor...

oh great, forgot to mention timing cover is off and front crank pulley is off to get timing cover off. Any other way to keep engine from spinning while turning torque converter bolts? To bad that flange or "C" cups wasn't also designed up front would make removal of drive shaft without...

Well pretty much a noob question and I need to ask... The plan was to drop the K member for an engine swap...But the rear 12 point diff flange bolts need Impact to get off and the infinite wisdom of design lacks "C" caps on ujoint front or rear, or A wider flange so 12 point bolts are not...

Going to toss this up in this thread, cause this is what I'm looking at but worse. So here it goes...on mine it looks like some one grabed the metal line with vice grips and nearly pinched the line closed on the botom line lower than this picture on the radiator. Well I seen it and said screw...

Uhm...Looks alright to me? I just looked at mine pass side,:confused: looks the same as mine. Is it just me,?:( I don't see whats wrong. Could you point at whats wrong...If you think somethings wrong with yours and its the drivers side send it to me I could use a match, maybe putting that one on...

At least his lemon moves more often than mine

[IMG]

[IMG]

[IMG]

[IMG]