My car FINALY goes in on Wednesday for the tune. Originally I picked up a SCT old X2 for the job. However some things have change with SCT and they only support my system with the "race pack" for $350, don't need a flasher. My tuner said I could also go to Diablo Intune. Those are $400. I to.d...
The steering wheel on my 98 is flaking so I found another black column and wheel, $100. First glance I thought I had the right color. From the picture you can tell they don't. The wheel is much blacker, if that makes sense.
Question is do I switch the plastic covers on the column so the wheel...
Not sure what these are worth used... $250 shipped to your door?
If you don't like the color of the tubes I have a glass bead cabinet and can strip it off for you. I have some couplers and clamps I will send as well.
Du
262-909-8608
I had to reclock my SC, previous owner had a different setup. Upon disassembly I noticed gray sealer. I cleaned it all out and got it where I needed and setup all of the tubing runs. I pulled it back apart to polish it up before final assembly.
What do you think I should use?
Thanks guys...
I did the cobra intake conversion and looking for some ideas for the IAC tube...
I am putting in a Paxton and have to make the tubing from the SC to the TB anyway. So I have the chance to use anything we want for a fitting.
I could use a piece of 3/4 heater hose... Trying to avoid this. Open...
Looking for a single gauge pod for my AEM combo gauge. I am looking for a solution where I don't have to cut up the dash or holes in the A-Pillar. Any other suggestions for gauges that are must have I am all ears...
Thanks
I can't get the cast aluminum Vortech stuff to fit like I was hoping. I am starting to think that some of the challenges I am having that others seemed to breeze through has to to do with using a Vortech bracket and a Paxton 1500.
I can only find a 4" throttle body Boot adapter that is 4" and...
I am doing the cobra intake swap with cobra fuel rails. Just to make sure I am doing this right....
I pull the passenger wheel well liner. I run a new pressure line from the filter to the rail. I will also find a connector for the return as well to run to the rail?
Use Dorman repair fittings...
I have the Vortech cobra mustang outlet piping. I have what I believe to be a lightning 4" OD MAF sensor. I don't see these two piece blending together to make a blow thru setup, at best the Vortech stuff is 3".
Do I make a new set of tubing 4" or do I weld the 2005 and up mustang MAF fitting...
I measured my inlet on my Paxton and it is 3 3/4 aka 3.75.
I need an elbow coming out obviously to the air filter and tubing, do I want to run aluminum elbow tubing with a coupler or a silicone elbow? I am thinking the silicone elbow would be better for install in case I am close to the fan...
I dropped the tank on my 98 to put in my new AEM fuel pump. All is going well, I trimmed the hat to fit the pump and swapped the wires around for,the electrical connector.
Problem: The nipple on the pump is taller than it was originally and the hump thing doesn't line up with the other one...
Since I am putting the centri on I need to do something with the coolant crossover. I refuse to pay the money for the Vortech tube. The On3 kit looks pretty nice and the price isn't to bad.
It seems there are two different paths to take for the head cooling mod. I see some that tie into the...
Let's see if this section gets so e action - the HP area is kinda dead.
98 LSC - Paxton 1500 hoping to aftercooler in case it matters.
Getting down to the a few more details...
Plugs Autolite XP103 - what gap do you think? .045 closed enough? They are one range colder than stock and same temp...
98 LSC - Paxton 1500 hoping to aftercooler in case it matters.
Getting down to the a few more details...
Plugs Autolite XP103 - what gap do you think? .045 closed enough? They are one range colder than stock and same temp as 03-04 cobras.
Delete or keep EGR? I am thinking delete it as well as...
Done a ton of reading here and on LOD most of it is pretty dated and I assume that after a while we change opinions.
Investigating injector size as I am collecting parts. In another thread a member told me to get the Cobra ones, 39lb(?). I only got one response. :(
98 LSC - NOVI 1500 and...
I am looking for a black stering wheel and maybe a driver door panel. 1998 Mark VIII LSC Black on Black
I looked on Ebay and everything so far is as bad as mine or worse. The steering wheel has the typical delaminating on the top half. The door panel has the same on the door pull.
I am in...
I have a stock 98 LSC with a TL on its way, be in hand for next weekend. Supercharger likely over the winter. Sometime between now and end of summer Jmod, higher stall and dual exhaust manifolds back. This will be a street car only with maybe a night at the strip once a year. I want to be able...
I am on the hunt for a Mark and seem to keep finding less than desirable vehicles or showing up one day too late. I had one 10 years ago and traded it in. I have been kicking myself for years and now I have decided to get one back.
I want a black and black car. 1998 LSC with the chrome wheels...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.