"Mark of the Devil" project pics.. finally

heres some pics of the custom grill i'm working on... my first body guy didnt do such a good job so im giving it to someone else... should be done and on in the spring..

still needs mesh and finishing...

grill1.jpg


grill2.jpg


grill3.jpg


grill4.jpg
 
I had to roll mine until the lap was layed flat against the inside of the quarter in order to get enough clearance..
Click to expand...

what modifying did you have to do to the bumper cover??.. im still not sure if i wanna take the chance by rolling the fenders and/or cutting the bumper cover....

and how much did you bring the camber in??
 
devilchild said:
what modifying did you have to do to the bumper cover??.. im still not sure if i wanna take the chance by rolling the fenders and/or cutting the bumper cover....

and how much did you bring the camber in??
Click to expand...


I used a razor knife and cut off where the top mounting screw is facing forward towards the wheel, then tapered it down close to the second screw, then smoothed it out, and painted it. It sounds cheesy as hell, but if you look at it, you can't tell it didn't come that way. Anyone who hasn't done that doesn't cruise as low as I do unless they're running some 14" daytons.

Lowering the car actually brings the camber in, I took it back out where it should be is all. Without doing that I doubt the 275's would clear on the inside when driving. I put my wheels on, backed the car up a couple times in the driveway, rolled the lips, cut the bumper, then trailered it to the alignment shop. All which wouldn't have had to be done if I weren't so low while running the BFG 275's. Three guys at the alignment shop laughed at how close all my clearances are. I have no space anywhere, yet don't rub.
 
ONEBADMK8 said:
That grill looks familiar. Waterfront pics dude, asap. That thing is looking evil.
Click to expand...

haha.. similar to yours.. only not as open... plus instead of mesh im thinking a powder coated sheet of stainless with vents stamped out of it..

and as for the pics...im still waiting for the hood :( :( .. he got real busy so its on the back burner
 
just got my Cobra R hood back from paint !!!!!

i get my final adjustments when i take it back to be buffed in a few weeks..

.. and the LMS 3-piece wing is about to go to the body guy...

hood 002.jpg


hood 003.jpg


hood 004.jpg


hood 005.jpg


hood 001.jpg
 
Lookin good I love black Marks !
Geno's hood tops that car off ! :cool:

My next one is gonna be triple black gen 2:)
 
Beautiful looking car! A magnificent job. Congratulations.
Those Nitto tires are very sweet as well. Lots of grip.
 
Absolutely Beautiful...........Just WoW Great job Man.........
Love the BLACK marks
 
kustomizingkid said:
PoniesVIII- Are you running the inner fender skirt on the front of your car?
Click to expand...

Yes. It's actually loose cause I's on the side of I35 500 miles from home at 2 a.m. with no patience and the f'n hose to the compressor i'd just replaced wasn't pushed in far enough to keep a seal. Got down on my stomach and ripped it past the bumper cover so I could get my ARM back in far enough. ..and still no rubbing.

..In case you were curious about clearance. Brad did a better job on the offset and backspace of these wheels than anyone could've purposely calculated for. Front and rear, flawless fit while slammed.
 
thanx all.....

3 piece wing is next.. i have it already... just waiting to take it to the body guy...

i also have all extra trim pieces that im also dropping off to be painted black..

and the custom grill..

all at once is what im hoping for..

but only time will tell..
 
You must log in or register to reply here.

Members online

No members online now.
Total: 93 (members: 0, guests: 93)
Back
Top