Search results

Awesome pics, how does the middle assembly attach to the dwn pipe into the intake? I have leak were those two connect Awesome pics, how does the middle assembly attach to the dwn pipe into the intake? I have leak were those two connect

Awesome pics, how does the middle assembly attach to the dwn pipe into the intake? I have leak were those two connect

well it was fine for a day, back to square one, just dont under stand why it smooths out an then just start missing, i changed the # 4 just in case of the rf interference. i looked for where the wires go to the firewall, goes under where the cabin filter is. i will take out the glove box in the...

I was looking at the wiring from each side of the valve covers, they are ( except for at the back of covers) inside looks like a harness, would i have to pull them out of that heat shielding ( assuming) and trace for breaks? and was just looking for the pcm, u say i can access from pass side...

wish i could take off fri, but i only have two days of vac left saving for xmas with the kids. im all ready to climb under the hood with you suggestions, can do the continuity and pwr test , not sure about the checking for short to gnd. any suggestions how to do that?

i plan to do all of your suggestions i figure the PCM will run about $1500 in up and running. ill spend my time this weekend on it, cant make the deer lease.

only pic, yes it does snow in texas sometimes..

awsome, i will have to wait till this weekend, in texas gonna be cold and wet. gotta love it, but i will do what u recommend, sounds like a solid start instead of trusting the dealer. i did check where u are talking about where the wires exit the back of the valve cover and they run thru some...

oh, sorry just wanted to thank you for any help given, it is very much appreciated. again ive have my share of issues, rear window track replaced under warranty, the climate control replaced, warranty, stop counting cop's under warranty, and more after, still have the door open light...

yes, #5 front driver side, the engine is very clean and inside the covers the connectors look new, and i replaced 5 and when didnt work i swapped coils and still same code. i look very carefully at the wiring to all cops on that side, i will try to find the pcm and check connections there. i...

ok, i got home today, no fail safe mode, just missing pretty bad, seems to get worse as you accelerate. if you keep it steady speed or its in park it seems to even out, if u rev its start missing again, hooked up the scan tool and now its showing po355 ignition coil E primary / secondary...

was headed home from getting my daughter and my 05 ls sport v8 went into limp mode, i finally made it home . freaking i killed it in the drive way and waited for my boys to get home to watch there sister while i hooked up my code scanner. got the p2110/p2107 actuator control module. however this...

was headed home from getting my daughter and my 05 ls sport v8 went into limp mode, i finally made it home . freaking i killed it in the drive way and waited for my boys to get home to watch there sister while i hooked up my code scanner. got the p2110/p2107 actuator control module. however...

did notice that it didn't run better till i cleared the code, was wondering if computer shut dwn that injector or cop, I did run it with a miss for, guesstimate 100 miles. waited till had the money for scan tool. Tired of driving to Autozone.

replaced COP on # 5 cleared the all codes seems to run OK.:p

where did u find that gauge display and what does one cost? WAY COOL ..

What did you use to attach to the roof? Mine is loose at the sunroof and brake light, used gorilla glue and not strong enough.

received my jbl speakers p8662 for my front doors will install this weekend, for the velcro in the headliner did it detach from the roof? mine did around the sunroof and the brake light, tried using gorilla glue to attach and not even close to strong enough.

Hello, my name is Richard and this is the first forum I've ever joined. Not very computer oriented so forgive my lack of knowledge for using this forum. Lol im already getting email to post. This will be learning process for me so forgive me if Im not using correctly or replying in right...