I can remember where I found this online but it has saved my ass multiple times. This has all the wiring diagrams you could want. It seems to view better on my phone for some reason though.
Start checking around the transmission. My first thought is it could be something simple like a connector unplugged because that is a lot of issues at once....
1. Gear display error: that is an input from the range sensor
2. Traction control error: could be from the vss issue.
3. Engine temp...
That was the plan gotta pull the trans to deal with some other stuff. When the engine was on the stand it was in there pretty good. Hopefully it comes out.
Since the 3.27 rear gear is still in there it is really tall but mechanically transmission and engine work perfect. If I could do it again I would have went 3.55 or 3.73. Also the rear end is gonna need some help. Stiffer bushings and such. It wheel hops pretty easy.
Ya it was partially a cost based decision. I figured with the stainless it wouldn't have an issue with rust but hadn't heard about the cracking. Also I didn't realize that local guys were that cheap. Jet hot wants like 500 or more to do V8 headers
I have a slow coolant leak coming from the flange on the passenger side head that feeds the heater core. it has two pipes connected to it. One goes to the head and the other travels through the v of the engine to the water pump I think... Both feed the heater core. Is this flange an o-ring seal...
Car is pretty much finished. It runs a drives great there are a few things left to iron out but overall the project was a success. I didn't take to many photos towards the end but started to video the process part way through instead. Here is a link to the first video!
Crossmember location was close enough to reuse it. The Heighth from output shaft to the bottom of the transmission mount was within a 1/2 inch of the old transmission. It should line the drive shaft up the same through the tunnel. Fingers crossed.
This extra metal was connected to the...
91 lsc le, I was under the impression that with a one piece trans were the bellhouseing is not separate it was not necessary for a concentric check according to my trans guy. I could be wrong though.
More progress! I got the motor put back in and started reconnecting things. Tidied up the ecm mount installed the clutch master and the stainless braided hydraulic line. Had to use the persuader to make room for the steering shaft near the headers.
I am glad I wrapped these the tolerance is...
Might be stupid question. Did you check the plug? Just throwing out ideas out hear but could the ressistance of the path through plug be to high. Google seems to indicate this is the most common cause of coil failure. Never ran into it myself just the first thing that popped into my head.
Does anybody know what this sensor is called. I broke the retainer for the pin inside the connector and I am looking to get a replacement. Single wire sensor grounded through the engine I'm guessing. There is one on each head. Thanks
I have been working on this for months in what little spare time I have. I just now decided to post it lol. I decided to keep the gears. I'm hoping the lower first gear in the 5 speed will pick it up enough off the line
.
Firewall pre cutting and mounting of new clutch pedal.
Harness extension
Tight fit!
Bracket with the in the process of getting the old tabs removed
New ecm location. Mounted in three positions to the dash frame.
powerwashed with new motor mounts
While the motor is out I am doing front...
I thought i would share my progress with you all. I did a j-mod which after installing ruined the 4r70w for reasons i'm still not sure on but I will not get into. I decide to say F@*k it and install a tremec 3650. Feel free to ask any questions or suggest anything. I will also be doing some...
Tell me about it I have had this truck for just a few months and that is on my to do list but it has ben non stop projects and that is lower on the list. The cam went flat the second month I had it. This is what it did to the lifter.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.