Search results

I just replaced all 4 struts and had no problem except the last one I did. The front passenger side. I can't get the top nut that holds the assembly together to tighten down far enough. The driver side there is about 7-8 threads showing, which is how the stock struts were, but the passenger side...

just read this from the repair manual. pretty sure this was my problem... "A low state of charge (SOC) in the vehicle battery may cause the PATS to allow the starter operation, but prevent the fuel injectors from operating."

ok so i cant figure out what i need to do to get rid of this bulb warning message. ive got the stock bulbs, and 2 different sets of LED bulbs, i wired the resistors in exactly as it shows on here, still got the message, tried different LED bulbs, still got warning message. so i measured the...

And my jump pack is 2000A max btw. Not that it really matters at this point lol

Is the "PATS light" on the gauges? Or the red light on the dash that blinks? And I did pull the codes, it said exactly that I'm pretty sure it was P1260 and "engine disabled by PATS" is what it said. I got it started. I left it on a slow charger overnight and then the next day my buddy suggested...

A few different places I've read now say that when pats disables the engine, it also disables the stater. Mine had a "engine disabled by PATS" code, but it would still crank? So now I'm really not sure what to do?

I was doing some work on my car and must have left the key in or lights on or something and the battery went dead. I hooked a jump pack to it and it cranks just fine,but won't start. So I checked the codes and there was a code "engine disabled by PATS" but I'm not sure why, I'm using the factory...

I was just curious if I could use my own, cheaper primer, and possibly my own cheaper clear coat with the color code matched base coat. On a side note . I bout 3 different factory color code mstched touch up pens, manufactured by Ford supposedly, from 3 different online retailers, and none of...

Well also, think this F6 tri coat pearl white would be even more expensive cuz is a "premium" paint job

there's cheap places here that will paint a whole car for $300 lmao...I remember seeing an ad for $299..that was prob. 15 years ago but still...imagine the high quality paint job you'd get for that premium price haha

Well, I don't really see myself keeping this car more than a couple more years, I tend to want something new every couple years and trade in lol.and even if I don't,I'd rather have a couple years of matching paint that eventually fades to slightly mismatched, than have the currently mismatched...

05 LS8

Sorry crappy video but was excited to finally get my color chase halos installed !

Anybody know much about paint? I have a few spots I'd like to touch up,and possibly even a fender I'd like to paint. I hit a guard rail on the interstate,and had to completely replace the front passenger side fender,didn't realize the junk yard fender I got was from like an 01 I believe and mine...

Well,right now I have 10w 100ohm resistors like u said, how much should I bump that up ya think? I do have more of those resistors cuz i bought a 10 pack, think just adding another in series would make it work? Or be too much?

Ya i was going to try different size resistors but wasn't sure what to get jus cuz like u said, idk what resistance the computer is looking for. I suppose i could measure the resistance of the old bulbs huh? And get something that closely matches? I'm guessing it's probably pretty close, since...

Also, I can't believe the prices that v LED store is charging! Like is that a joke? Theyre smoking crack if they think I'm gonna pay $180 for a set of LED bulbs. A set of LED bulbs that cost them less than a dollar to manufacture, and that I can get similar quality for 20 bucks on amazon...And...

*7 years later...lol* I just did this with my tail lights, used 2 10w 100ohm resistors, exactly as the diagram shows, the lights work as they should, and i dont get "check brake lights" but i still get "check tail lights" warning message. i have a gen 2 2005 LS Sport. I used these bulbs and...

ok so i could access that "keypad_code" from the screen where i can choose sensor data to show on the android app, but that 5 digit code didnt work. i tried with the full program on my laptop, and that sensor data thing shows the same code, but then theres one of the service functions that says...

None of the links in OP work...