Search results for query: *

Anyone know where to find an Oil Level Sending Unit for a 97 Mark VIII 4.6L. My mechanic has exhausted his sources with no luck. Thanks in advance for your help.

97 MKVIII Recently my A/C started smelling like the inside of a nail salon (don't ask how I know) it get's worse over time, then disappears after the car is parked for a while. A/C still blows cold and functions fine. I used the car the other day and there was no smell. My Mark stays parked most...

My Mark has problems with the traction control. Makes a grinding from the rear like a stuck caliper. Check traction control light comes on as well. Turning off traction control eases grinding somewhat, but still present. Have not had a chance to pull wheels, but will this weekend. Any checks...

Got a check engine light and code reader says PO 161 (o2 heater circuit). Anyone got a link for downloading flow chart for testing this circuit? Where to order factory manual? What is bank order 1-2 as in driver-passenger? 97 Mark VIII no mods Thanks, Eddie

My Mark has begun eating the trans. When leaving from a stop in drive, it grinds and hesitates as if the the brake caliper is hanging up. It only does it leaving from a stop and at low speed (parking lot crawl). It drove fine on the freeway and started exhibiting symptoms on the street. I just...

Anyone know where I can find a new rear window seal for my Mark? The dealer in my area no longer carries and I would like to replace this seal after repainting.

I converted my MarkVIII to coil springs. Anyone know where I can get a core charge for my old bags?

I'm looking for a set of new wheels for my Mark. Has anyone worked out rubbing and backspace issues, widest width that will fit without interference? I like the look of 20s but don't want the rubberband sidewall. I do a bit of canyon carving and like the idea of a performance 18" with enough...

Help!! I have no heat in my 97 MKVIII. I saw a post on here a few years back regarding the procedure for fixing it. It seems to be a controls problem. No heat enters cabin at all. No defrost either. I have lived with this problem for years and swore this would be my last winter without heat...

My 97 MKVIII has a cracked lower intake manifold. The dealer no longer stocks the part. Any ideas on aftermarket replacement or Motorsport p/n ? I'm looking for direct replacement compatible with rest of intake assembly. An upgrade over stock would be preferable, but stock manifold will be...

My Mark has recently developed a major vacuum leak in the intake valley area. It appears to be the manifold itself as a spray test and visual inspection reveals no leaks in the upper area of manifold or connections. The leak is a solid, loud hiss but only affects driveability intermittently. It...

I'm looking for a new caliper bracket for my mark. The pins are frozen in place and I don't want to muck up the bracket removing them. Have tried all means to remove and they are rusted solid. I'm looking for left rear bracket and pins. Thank you for your help

Anyone know where I can find an outer door handle (pass) for my mark other than buying from the dealer. They want $70 but can't guarantee when part will come in. Also trim is coming unglued on inner door panel where leather meets the window. Any recomendations ? 3m trim adhesive ? Thanks for...

I'm getting ready to upgrade to drilled rotors and wanted to replace grease seals on hubs and pack bearings while I'm in there. I went to Auto Zone and they said they don't stock seals for MKVIII, but sell a hub/bearing/seal assembly. I don't mind upgrading but this seems unecessary if bearings...

Yes, I know it's a pretty weak subject. My cupholder broke and I need to locate a replacement. It started hanging up and would'nt close then just broke off recently. Anyone know where I can locate one ?

I'm ready to go with a coil spring conversion and am wondering what options or suppliers have this kit. I'm interested in lowering at the same time. Anyone done this conversion ? Level of difficulty ? I plan on this being a driveway job. Any issues during install ? Also, what happens to the...

I need to R&R the ball joints on my 97 MKVIII. My local shop wants $600+ to replace. I'd rather do it myself. Are there any special tools or procedures involved. The arms look a little delicate compared to the "old school" steel arms on my Stingray and I don't want to mangle them in the process...