Search results

Stopped at a deli for lunch yesterday and went to step out of my truck and crack the running board dropped a like two inches and was somewhat loose. The aluminum swing arm bracket/bushing housing was corroded to the point it disintegrated. lucky the ebrake cable help it up so I could get it home...

Magnaflow 12568 dual 2.5" in dual 2.5" out x muffler. This was going to go on my Mark VIII still in the box $65 plus shipping. That's half price Boston S85 6x8s. NIB never used. I think I bought them for the LS and went with separates instead. $30 plus shipping

I don't have an LS anymore, but the 05-06 Navis have the same fog lights as Gen1 LSs. Has anyone opened the housings up? If baked will they pull apart like most headlights? And can anyone tell me a measurement from the inside of the leans to the inside of the bulb socket? I'm going to try and...

Anyone want to head down? I'll be there and my buddy who bought my Mark will be taking the car on it's first 1/4 miles runs. Any predictiones for the Mark? Canned tune, 4.10s, 3500 stall and stock size tires.

Any near NJ come out tomorrow. I'll be there.

My dad has a 2001 Taurus with intermittant electrical issues. Sometimes the windows/moonroof do not work, sometimes everything but the anti theft light does not work including headlights and the horn. And sometimes we get varies stages of electrical things not working along with a no crank when...

I'm looking at something else and it works out I need to get rid of the LS. If not I'm keeping the car until I find the right replacement, however long that might be. 06 Silver Birch on black 34k miles 19" Mille Miglias with near new summer tires factory 17s with new Pilot Sport a/s K&N...

1997 Mark VIII base Evergreen over Prairie tan 85K miles, interior is clean for age mileage. A couple guys on here have seen/been in the car and can vouch for the condition/maintenance of the car. Since I've had the car I've replaced the following... New head gaskets Valve cover gaskets...

Custom ground for the heavier Mark Comp Cams never installed sill in original boxes Intake lobe profile 9342 475 lift 226 dur lobe sep 111 exhaust lobe profile 9320 450 life 220 dur lobe sep 114 You WILL need aftermarket springs to run these cams. Asking $800 shipped JLT...

My sister has a 02 Taurus that sometimes when first started up the windows and moonroof don't work. If you drive the car for a few minutes they start working again. It's random when it does it or works fine. Anyone have a clue? Is there a module that runs the windows and the moonroof?

I need a new socket for the 3157 signal bulb in my gen2. I ordered one but where the upper signal socket mounts is different then the lower tail/brake light mounts. It fits on the bottom not the top. Anyone know where I can get one that will fit?

Hit me up with how much shipped to 11779. Thanks

Ported short runner Cobra intake. 1" taken off the runners bell ends reattached. $500 Cobra fuel rails $75 Aluminum home made IMRC deletes. butterflies rods removed ends epoxied $75 Comp cams custom grinds never run. Still in original boxes. 475/450 lift the rest I have to verify but...

I have searched and read through some old posts but it's hard to find difinitive answers. I am looking at either 18 or 19s 8.5" wide with a +42 offset. Stock ride height now but Eibachs are probably in the near future. Any help on what the widest tires I can run without rubbing would be great.

Right now just gauging interest as we need a decent turn out to make this work financially. The Mark VIII of the State of NY Club is trying to put together a dyno day. Right now we are shooting for a Sunday in June in Babylon NY. Would be all day and include food if everybody wants to hang...

Right now just gauging interest as we need a decent turn out to make this work financially. The Mark VIII of the State of NY Club is trying to put together a dyno day. Right now we are shooting for a Sunday in June in Babylon NY. Would be all day and include food if everybody wants to hang...

Started installing the DDM tuning HIDs/bulb out warning eliminators/relay harness last night. Checked both sides to see if the ballast worked or I would have to do the reverse polarity thing. Both sides worked fine. Called it quits when it got dark. Back at it this morning which pretty much...

I have the new halogen housings on the car but have my cloudy as hell originals packed away. I was thinking about opening them up and trying to the chrome besides the actual reflectors. Anyone open these up before? If so how did you do it dremel bake them in the oven?

When driving over bumps or imperfections in the road I get some rattling in the drivers door. It also buzzes with the stereo. I took the door panel off and didn't have much luck identifying where it's coming from. The car is quiet enough for me besides this annoying rattle and I'd rather fix the...

No HID bulbs so don't ask. The need to cleaned up. A few passes with plastic polish makes them acceptable but definitely not perfect. Personally I would sand them and polish or clear coat them. Asking $100+ shipping